A Frequent Garage Door Issue That Arises From Multiple Causes.
If your garage door starts to lift and then suddenly comes back down, you are dealing with one of the issues garage door technicians get called about most often. It can seem like the door has a mind of its own, but there is almost always a real reason behind it. Modern garage doors are built with several safety features that stop the door whenever something seems off. A door that reverses on its own is simply one of those safety features doing exactly what it was designed to do. The encouraging part is that most of the reasons behind this behavior are simple to track down get more info and repair. The frustrating part is that more than one thing can trigger the same symptom, so you have to rule them out one by one. The steps below follow the same checking order a trained garage door repair technician would use, which means you may be able to skip a service call if the answer turns out to be an easy one.
Begin by Inspecting the Photo Eye Sensors
Begin your troubleshooting at the photo eye sensors. Look for two compact black devices fastened low on each side of the garage door frame, sitting only inches above the ground. The pair works together: one sensor projects a beam of invisible light, and the other one receives it. Whenever the door is in motion and something breaks that beam, the safety system instantly sends the door back up to avoid crushing whatever the sensor saw. Approach the door and visually inspect each sensor closely. Both units have to point directly at each other, completely level and on the same plane. You will usually see a small status light built into each sensor, either green or red. Most of the time, green confirms normal operation. Red indicates that the beam is being blocked or that the sensors have shifted out of alignment. Check around each lens for cobwebs, accumulated dust, leaves blown in from outside, or any random item that may have ended up in front of it. Give both lenses a gentle wipe with a soft, clean rag. If the red light still glows after cleaning, slowly adjust one sensor by hand, moving it just slightly, until you see green lights on both sides. Realigning or cleaning the photo eyes resolves roughly half of all reported garage door reversal issues.
Inspect the Garage Door Tracks for any Obstructions.
If the sensors appear to be functioning properly, the next thing to inspect is the door’s tracks on each side—those metal rails that guide the rollers up and down. Frequently, a tiny object can become lodged in the track, such as a stone, a child’s toy, or a piece of cardboard from a shipped package. When the door lifts, it strikes the obstruction, and the opener interprets the resulting resistance as an unexpected obstacle, prompting the safety mechanism to reverse the door’s motion. Examine both tracks from top to bottom while the door is fully open and clear away any debris. While you’re at it, look for rollers that may be bent or broken, since damaged rollers can also generate resistance that the opener detects as a problem.
Inspect the Door’s Springs
Just above the door opening, you should see one or maybe two thick metal coils stretched across a horizontal bar. These are known as torsion springs, and they actually carry most of the weight when the door rises. The opener motor is doing far less work than people assume. Its main job is steering the door. The springs handle the heavy lifting. Once a spring wears down with age or snaps completely, the door turns into a very heavy load that the motor wasn't built to lift on its own. After climbing only a small distance, the opener exhausts its strength and sends the door back down. To inspect the springs, look closely at each coil for a noticeable break or split in the wire. When a torsion spring snaps, it usually leaves behind a visible gap of about two inches right where the steel parted. If you do find a broken spring, never attempt the repair yourself. Torsion springs are wound under enormous tension and can release that energy violently, leading to serious harm. Replacing them is work for an experienced garage door professional. Expect the cost of the job to fall somewhere between two hundred and four hundred dollars.
Test the Door's Balance by Hand
Springs can appear normal to the eye while quietly losing the strength they once had. To find out whether yours have weakened, run this quick test. Locate the red emergency release handle that hangs down from the rail beneath the opener, and give it a firm pull. Pulling that handle disengages the door from the motor so it can be operated by hand. Next, lift the door yourself using just your arms. A door with good springs and proper balance will feel almost weightless. A single hand should be enough to raise it, and once you release it around the midpoint, the door should remain in place without sliding. If the door feels noticeably heavy as you lift, or if it slowly drops back down after you let go, then the springs have begun to lose their lifting capacity. This kind of spring weakness sits behind a large share of reported cases where doors reverse before reaching the top. Once your test is complete, push or pull the release handle in the opposite direction to reconnect the door to the opener.
The Force Dials on the Back of the Motor
Every garage door opener has two small dials or buttons on the back of the motor housing. One controls the force used to open the door, and one controls the force used to close it. Over time, as parts wear and seasons change, the opener may need slightly more force to do its job. If the force setting is too low, the opener thinks any resistance means it has hit something, so it reverses. The owner's manual for your LiftMaster, Chamberlain, Genie, or Craftsman opener will show you exactly where these settings are. Adjust the open force dial slightly upward, then test the door. Adjust in small steps. Setting the force too high creates a safety risk because the opener will keep pushing even when it shouldn't.
Check out the Travel Restrictions Settings
The opener's travel limits determine the upper and lower points the door should reach. Incorrectly set limits the opener to mistakenly door has reached its reverse its direction. This issue outage, installation of a new opener, or maintenance work on the door. Similar to settings, the controls for adjusting the travel limits are located on the back opener motor. Referring to the manual them a simple task. If the door now travels too high or too low, it indicates a problem with the travel limits that should, even if the door is not completely reversing.
Chilly Temperatures May Trigger the Same Issue
In winter, a stiff and cold garage door can put extra strain on the opener. Old grease in the tracks becomes thick, rollers don't spin as smoothly, and the door becomes harder to lift. The opener works harder, hits its force limit, and reverses. If your door only reverses on cold mornings and works fine the rest of the day, this is probably what's happening. The fix is to clean the tracks and lubricate the rollers, copyrights, and springs with a garage door specific lubricant. Avoid WD-40, which actually cleans grease off rather than adding it. Use a lithium or silicone spray made for garage doors.
When It's Time to Call a Garage Door Technician
If you've checked the sensors, the tracks, the springs, the force settings, the travel limits, and lubricated the door, and it still reverses, it's time to call a garage door repair contractor. At that point, the problem is usually inside the opener itself — a worn drive gear, a failing capacitor, or a damaged logic board. These repairs need proper tools and parts. A good technician can diagnose and fix most issues in under an hour, and the visit usually costs between one hundred and two hundred dollars before parts.